DIY Gallows Tool

kind of self-explanatory, right? We seem to have some impressive thread-wrappers that lurk around this board. let's try to keep your "first booger" posts at a minimum.
Post Reply
User avatar
ScottP
Posts: 2811
Joined: Fri Mar 21, 2008 7:22 pm

DIY Gallows Tool

Post by ScottP » Sun May 31, 2015 8:35 am

Since I started tying Hacklestackers, I tried a bunch of different ways to hold the post loop while wrapping the hackle (never did get the hang of the mono loop on the finger like Mr. Quigley tied it). DIdn't feel like buying a gallows so I tried everything from bent coat-hangers to rubber bands on the Ott light that hangs over my vise. Rooting through the bins at Home Depot for another project, I found some nylon spacers that fit the vise shaft and figured they'd work as the base; just needed the right material for the hook part. Coat hangers are a bit thick and really don't have that much spring to them, same with all the spooled wire I could find. Thought about stuff like 304 spring steel wire, music wire, etc, then remembered the wire on those cheapy marker flags might work (grabbed one from the neighbor's yard - I'm sure they won't have any trouble finding those buried cables they're going to start digging around). The stuff is perfect - flexible, doesn't seem to have much memory, provides the right amount of tension, and is long enough that when it's bent and attached to the post loop, there's plenty of room to wrap the hackle without banging into it.

base - nylon spacer 3/8" I.D. x 1" x 3/8"
arm - 1/6" wire (from marker flag)
glue - 5 min epoxy

spacer; drill 1/16" hole

Image

Image


flag (pull the flag off and clean up the wire with a little steel wool)

Image


bend end of the wire into a hook

Image


epoxy other end into the spacer

Image


slide it on the vise shaft and Bob's your uncle

Image


Image

Image

Image

plenty of clearance for wrapping hackle

Image


finished product

Image


a better shot of the setup; the wire's about 20" long so it describes a decent-sized arc.

Image



total cost - $.50 for the spacer
Everyone stopped to stare at your technicolor motor home
RIP Walter

User avatar
DizzyDean
Posts: 691
Joined: Wed Nov 23, 2011 10:53 am
Location: Calorevada

Re: DIY Gallows Tool

Post by DizzyDean » Mon Jun 01, 2015 5:36 pm

here's some photos that might help you with the hackle part

https://rustyhooks.wordpress.com/2013/0 ... p-by-step/
my blog from the Sierras

http://rustyhooks.wordpress.com

User avatar
austrotard
Posts: 9998
Joined: Thu Dec 06, 2012 2:24 am
Location: the austrocity exhibition
Contact:

Re: DIY Gallows Tool

Post by austrotard » Mon Jun 01, 2015 10:11 pm

we'll always have buffalo, sweet josh.

-mtice

User avatar
ScottP
Posts: 2811
Joined: Fri Mar 21, 2008 7:22 pm

Re: DIY Gallows Tool

Post by ScottP » Tue Jun 02, 2015 5:35 am

DizzyDean wrote:here's some photos that might help you with the hackle part

https://rustyhooks.wordpress.com/2013/0 ... p-by-step/
That's a real good SBS; think it was one of the sites I checked it out when I was trying to learn how to tie Hacklestackers. Never could get it right, using mono, Flexi-floss, Uni-stretch, poly, whatever - just couldn't get a clean handoff on the switch.
Everyone stopped to stare at your technicolor motor home
RIP Walter

User avatar
DizzyDean
Posts: 691
Joined: Wed Nov 23, 2011 10:53 am
Location: Calorevada

Re: DIY Gallows Tool

Post by DizzyDean » Tue Jun 02, 2015 2:14 pm

my blog from the Sierras

http://rustyhooks.wordpress.com

User avatar
DizzyDean
Posts: 691
Joined: Wed Nov 23, 2011 10:53 am
Location: Calorevada

Re: DIY Gallows Tool

Post by DizzyDean » Tue Jun 02, 2015 2:47 pm

ScottP wrote:
DizzyDean wrote:here's some photos that might help you with the hackle part

https://rustyhooks.wordpress.com/2013/0 ... p-by-step/
That's a real good SBS; think it was one of the sites I checked it out when I was trying to learn how to tie Hacklestackers. Never could get it right, using mono, Flexi-floss, Uni-stretch, poly, whatever - just couldn't get a clean handoff on the switch.

your right hand acts as the gallows, it just holds stuff in place, your left hand goes around everything and does most of the work.
my blog from the Sierras

http://rustyhooks.wordpress.com

User avatar
yard4sale
Posts: 2154
Joined: Wed May 28, 2014 4:12 pm

Re: DIY Gallows Tool

Post by yard4sale » Tue Jun 02, 2015 3:30 pm

DizzyDean wrote:
ScottP wrote:
DizzyDean wrote:here's some photos that might help you with the hackle part

https://rustyhooks.wordpress.com/2013/0 ... p-by-step/
That's a real good SBS; think it was one of the sites I checked it out when I was trying to learn how to tie Hacklestackers. Never could get it right, using mono, Flexi-floss, Uni-stretch, poly, whatever - just couldn't get a clean handoff on the switch.

your right hand acts as the gallows, it just holds stuff in place, your left hand goes around everything and does most of the work.
That's called the stranger. Same thing can be accomplished by sitting on your right hand first.
You can't go back and you can't stand still
If the thunder don't get you then the lightning will

When your choices are between a pedophile religious zealot or a dem suddenly the pedophile religious zealot doesn't sound too bad. - PLOW

User avatar
DizzyDean
Posts: 691
Joined: Wed Nov 23, 2011 10:53 am
Location: Calorevada

Re: DIY Gallows Tool

Post by DizzyDean » Tue Jun 02, 2015 6:14 pm

sounds vaguely familiar...

my blog from the Sierras

http://rustyhooks.wordpress.com

Post Reply

Who is online

Users browsing this forum: No registered users and 22 guests